»óÇ°Ä«Å×°í¸® > ÀüÀÚ ºÎÇ° > ÀüÀÚ¸ðµâ > Àü¿ø¸ðµâ

ºê·¹µåº¸µå ÆÄ¿ö¼­ÇöóÀÌ ½ºÆ½ 1.8v, 3.3v (SparkFun Breadboard Power Supply Stick - 3.3V/1.8V)
ÆǸŰ¡°Ý : 22,000¿ø (ºÎ°¡¼¼ Æ÷ÇÔ)
»óÇ°ÄÚµå : [3419]DEL
¹è¼ÛÀÏ : ´çÀϹ߼Û
Á¦Á¶»ç : Sparkfun
ºê·£µå : SparkFun [ºê·£µå¸ô ¹Ù·Î°¡±â]
³²Àº¼ö·® : 1°³
±¸¸Å¼ö·® :
°³
ÃÑ ±Ý¾× :
Ãß°¡&´ë·®±¸¸Å ¿äû 053-588-4080

  • »óÇ°»ó¼¼
  • °ü·Ã»óÇ°
  • ¹è¼Û/±³È¯/¹ÝÇ° ¾È³»
  • »óÇ°¸®ºä

4~9V ÀÔ·Â Àü¾ÐÀ» 1.8~3.3V·Î Àü¾Ð°­ÇÏÇÒ ¼ö ÀÖ´Â ºê·¹ÀÌÅ©¾Æ¿ôº¸µåÀÔ´Ï´Ù. 3.3V¸¦ »ç¿ëÇÏ´Â ÇÁ·ÎÁ§Æ®¿¡ »ç¿ëÇÒ ¼ö ÀÖÀ¸¸ç, ÀÔ·ÂÀº ¹è·²Àè ȤÀº 2ÇÉ Ä¿³ØÅ͸¦ ÅëÇØ °ø±ÞÇÒ ¼ö ÀÖ½À´Ï´Ù.

Description: This is a very simple board that takes a 4-9V input voltage and outputs a selectable 1.8V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard.

Input power can be supplied to either the DC barrel jack or the two pin header labeled + and -. Output power is supplied to the pins labeled GND and VCC. Board has both an On/Off switch and a voltage select switch (3.3V/1.8V).

The two sets of four GND and VCC pins are spaced such that when connected to our Basic Breadboard both power busses will be powered.

Note: Headers are not supplied. You will need to supply your own headers to connect this board to a breadboard. Check below for some breakaway header strips.

Dimensions: 2.15x0.65"

Features:

  • 4-9V input voltage via barrel jack or 2-pin header
  • 3.3V or 1.8V regulated output voltage
  • 800mA Operating Current
  • ON/OFF switch
  • Output voltage select switch
  • Power status LED
  • PTC fuse protected power
  • 5.5x2.1mm center positive barrel jack

Documents:

¸ÞÄ«¸®¿öÁî






°ßÀû¿äû
±¸¸Å´ëÇà
Äü/¹æ¹®¼ö·É
ÈĺҰáÁ¦
±â¼ú¹®ÀÇ