닫기
전체카테고리
  • 반도체/수동소자
    반도체/수동소자
  • 임베디드하드웨어
    임베디드하드웨어
  • 교육용키트
    교육용키트
  • 센서모듈
    센서모듈
  • 입출력모듈
    입출력모듈
  • 전원/파워/배터리
    전원/파워/배터리
  • 기타 하드웨어
    기타 하드웨어
  • 특가상품/리퍼상품
    특가상품/리퍼상품
  • 반도체/수동소자
    반도체/수동소자
  • 임베디드하드웨어
    임베디드하드웨어
  • 교육용키트
    교육용키트
  • 센서모듈
    센서모듈
  • 입출력모듈
    입출력모듈
  • 전원/파워/배터리
    전원/파워/배터리
  • 기타 하드웨어
    기타 하드웨어
  • 특가상품/리퍼상품
    특가상품/리퍼상품
적외선 라인센서 (즈모봇 디자인) / Zumo Reflectance Sensor Array 이미지 확대 보기
  • 적외선 라인센서 (즈모봇 디자인) / Zumo Reflectance Sensor Array

적외선 라인센서 (즈모봇 디자인) / Zumo Reflectance Sensor Array

공유
VAT 포함 가격입니다.
판매가
11,000원 (부가세 포함)
구매혜택
할인 : 적립 마일리지 :
상품코드
427269
브랜드
Pololu
제조사
Pololu
구매제한
옵션당 최소 1개
적외선 라인센서 (즈모봇 디자인) / Zumo Reflectance Sensor Array
0원
총 상품금액
총 할인금액
총 합계금액
적외선 LED를 통해 라인을 검출할 수 있는 센서입니다.

 This reflectance sensor module is designed for use with the Zumo shield for Arduino. It has six IR LED/phototransistor pairs that can be used for line following or edge detection; each sensor provides an independent, digital I/O-measurable output. The array draws approximately 40 mA when the emitters are on, and an optional input allows the emitters to be turned off for additional sensing or power-saving options.


Overview

The Zumo reflectance sensor array provides an easy way to add line sensing or edge detection to aZumo robot. It features six separate reflectance sensors, each consisting of an IR emitter coupled with a phototransistor that responds based on how much emitter light is reflected back to it. The two outside sensors are positioned at the very edges of the module to maximize their usefulness as edge detectors (e.g. for seeing the white edge of a sumo ring) while the four inner sensors are closer together for better detecting lines. This sensor is included with the assembled version of the Zumo robot, but not with thekit version.

The sensor array plugs into the front expansion header of the Zumo shield, which provides it with power and the necessary I/O connections. The default I/O connections are to pins that are otherwise unused by the Zumo shield, but the sensor module makes it possible to remap these pins or disconnect specific sensors altogether to free up I/O lines. Please see the Zumo Shield user’s guide for detailed information about assembly and use with the Zumo robot.

Zumo reflectance sensor array on a Zumo robot.

Zumo reflectance sensor array on a Zumo robot, bottom view.

Included components

The Zumo reflectance sensor array ships with all of the components you need to connect it to a Zumo shield:

Zumo reflectance sensor array assembled with included male header pins.

The short ends of the extended 2×12 male header strip should be soldered to the board as shown above (with the solder joints made on the component side of the array). The included 2×12 female header should be soldered to the front expansion area of the Zumo shield as described in the Zumo shield user’s guide. The array also ships with two 1×3 male headers: a straight version and a right-angle version. You can optionally solder the 1×3 header of your choice to the set of three holes along the edge of the board and use the included shorting block to connect the appropriate I/O line to the LEDON pin for dynamic control of the IR emitters (note: it is generally easier to install the 3-pin header before the larger 24-pin header). If you are content just having the IR emitters on all the time, you can skip installation of the 1×3 header. The assembled picture above shows the right-angle header installed.

How it works

QTR-1RC output (yellow) when 1/8" above a black line and microcontroller timing of that output (blue).

The array uses the same sensor modules as our QTR reflectance sensors and has the same principle of operation as our QTR-8RC version. The procedure for reading each sensor is as follows:

  1. Turn on IR LEDs (optional).
  2. Make the I/O line connected to that sensor an output and drive it high.
  3. Wait several microseconds to give the 1 nF capacitor node time to reach 5 V.
  4. Make the I/O line an input (with internal pull-up disabled).
  5. Measure the time for the voltage to decay by waiting for the I/O line to go low.
  6. Turn off IR LEDs (optional).

These steps can typically be executed in parallel for all six sensors. Our Zumo Arduino library provides functions for reading the sensors and controlling the emitters (as well as high-level functions for taking calibrated readings and determining the position of a line), so you do not have to program this sequence of steps yourself.

With a strong reflectance, the decay time can be as low as several dozen microseconds; with no reflectance, the decay time can be up to a few milliseconds. Meaningful results can be available within 1 ms in typical cases (i.e. when not trying to measure subtle differences in low-reflectance scenarios), allowing up to 1 kHz sampling of all 6 sensors. If lower-frequency sampling is sufficient, substantial power savings can be realized by turning off the LEDs. For example, if a 100 Hz sampling rate is acceptable, the LEDs can be off 90% of the time, lowering average current consumption from 40 mA to 4 mA.

To minimize the required emitter current, the IR LEDs are arranged in two parallel chains of three and powered from the Zumo shield’s boosted 7.45 V. Each chain of emitters is wired in series with a red LED, making it possible to tell when current is flowing through that chain (it is not possible to tell if the IR LEDs are on by looking at them with the unaided eye). All of the IR emitter LEDs are controlled by a single MOSFET that is gated by a digital LEDON input that enables the emitters when left disconnected or driven high. If this input is driven low, the emitters are disabled. Turning the LEDs off might be advantageous for limiting power consumption when the sensors are not in use or for varying the effective brightness of the LEDs through PWM control. Additionally, reading the sensors with the emitters turned off makes it possible to detect (and potentially compensate for) any ambient IR that might be interfering with readings. When the emitters are on, the sensor array draws approximately 40 mA.

Schematic diagram

This schematic diagram is also available as a downloadable pdf (211k pdf).

포토커플러 인터럽트(인터럽터) 스피드 센서 모듈 (Speed sensor module, counter module)
포토커플러 인터럽트(인터럽터) 스피드 센서 모듈 (Speed sensor module, counter module)
1,650원
[인디프로그] ToF sensor 거리 센서
[인디프로그] ToF sensor 거리 센서
21,780원
10~80cm 아날로그 적외선 거리센서 (GP2Y0A21YK)
5,500원
품절
GP2Y0D810Z0F 디지털 거리센서 10cm
9,700원
품절
[티원]실외용 광 거리측정 센서 / 라이더 센서 / 라이다 센서 / TFmini Plus LiDAR(Short-range distance sensor)
64,800원
품절

장바구니 담기

상품이 장바구니에 담겼습니다.
바로 확인하시겠습니까?

찜 리스트 담기

상품이 찜 리스트에 담겼습니다.
바로 확인하시겠습니까?

이미지 확대보기적외선 라인센서 (즈모봇 디자인) / Zumo Reflectance Sensor Array

적외선 라인센서 (즈모봇 디자인) / Zumo Reflectance Sensor Array
  • 적외선 라인센서 (즈모봇 디자인) / Zumo Reflectance Sensor Array
닫기

비밀번호 인증

글 작성시 설정한 비밀번호를 입력해 주세요.

닫기

장바구니 담기

상품이 장바구니에 담겼습니다.
바로 확인하시겠습니까?

찜 리스트 담기

상품이 찜 리스트에 담겼습니다.
바로 확인하시겠습니까?

  • 장바구니
  • 최근본상품
  • 위로
  • 아래로

최근 본 상품

0/2
우측 배너
고객센터

053-588-4080평일상담 : 10:00 ~ 17:00 | 점심시간 : 12:00 ~ 13:00
주말 및 공휴일 휴무

계좌안내

신한은행100-032-613560
예금주 : (주)메카솔루션